- #Amcc 3ware 9650se sata raid controller software full size
- #Amcc 3ware 9650se sata raid controller software driver
Sending them in for warranty replacement seems to be a method to just swap a flaky card for a different flaky card! Only a burn-in test for a few days reveals if a card will be stable under load. Typically one will see messages about the card being unresponsive and being reset and then it just does an outright hang and corruption of the data being manipulated. The failures are basically a flurry of parity errors. The QA people will not talk to me as I don't use their approved motherboards - but I've got 3 different motherboards (all Asus, 2 AMD, one Intel) which I use for testing - and a failing card fails on all of them.
A raid 5 array of 4 HDs will also fail - but it takes a few days instead of hours. A raid 5 array of 5 to 7 drives will at times crash the system so badly that the card is not detected unless the system is powered down. They all fail within 48 hours of burn-in testing on the provided firmware or the latest. Then a 2nd controller failed and I've sent the past 4 replacements back. The controller was unstable, when heavily loaded (just untaring a large tgz file), and would crash within a day of burn-in testing. It started with a hang on the backup box with 5 x 1.5TB drives. However, recently my experience with 3ware soured badly. I tested that before deploying as I have 4 and 8 port cards. I've got a stable of 3Ware 9650SE cards and swapping is easy. I'm afraid there is only LSI (now Broadband) to consider.Īfter Broadcom bought Avago they made changes to Avago website, drivers/downloads are harder to find for 3ware. If you use them still, sadly its time to swicth to something new. It's a pity that 3ware is no more, these are great products Installing 3dm2 and cli is working out of the box in ubuntu (tested: 14.04LTS, 16.04LTS), just run the shell script from the install. When building raids use the lower ports first, because you can also switch to a 9650 card with fewer ports easily as long as the higher ports are not used on the original card.Īvoid the first x16 pci express port on the motherboard, some motherboards are expecting video cards there, causing strange behavior. You can switch cards, but use the same firmware (or newer if same version is not available). They are still working (most of them made around 2007 perhaps?)ĭid not see a failing battery yet, after 8-9 years (using them in ideal conditions, batteries always checked, charged). The low profile 9650SE cards are later made and they work fine in modern uefi, etc. In older motherboards they work fine (tested in core2 motherboards).
#Amcc 3ware 9650se sata raid controller software full size
Some info on using 3ware 9650 raid cards in modern, common motherboards:Īvoid full size 9650 cards as they don't work with newer motherboards, bios fails to kick in after soft reset.
#Amcc 3ware 9650se sata raid controller software driver
Has anybody performed a card swap before?Įdit: These are the kernel errors we see: 3ware 9000 Storage Controller device driver for Linux v2.26.02.012.ģw-9xxx 0000:09:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18ģw-9xxx 0000:09:00.0: setting latency timer to 64ģw-9xxx: scsi0: ERROR: (0x06:0x000D): PCI Abort: clearing.ģw-9xxx: scsi0: ERROR: (0x06:0x001F): Microcontroller not ready during reset sequence.ģw-9xxx: scsi0: ERROR: (0x06:0x0036): Response queue (large) empty failed during reset sequence. We've ordered a new one, but I'm worried that if we replace the card it won't recognize the existing array. The OS eventually boots, but alas, without the card. We're using it in a Silicon Mechanics R272 machine with gentoo for the OS.
The firmware on it has been upgraded in the past, so it's possible we've hit some sort of firmware bug. Now, when we turn the machine on, the bios option rom that normally kicks in before the bootloader doesn't show up, none of the drives start, and when the OS tries to access the device, it just times out. This card has been in service for a couple years without problems, and was working up until the shutdown. We had to bring the server down for a pending power outage, and when we turned the machine back on, the raid card never started. We have a 8-port 3ware 9650se raid card for our main disk array.
0 kommentar(er)
